IEEE 1584 · Engineering
Arc Flash Study
## Arc Flash Study
What We Deliver
Key Challenges We Solve
Carelabs delivers IEEE 1584 arc flash studies for Argentine industrial facilities — from incident-energy calculation to printed equipment labels and AEA 90364-aligned mitigation plans.
Incident Energy Calculations
IEEE 1584-based calculations at every bus and panel to determine arc flash boundaries and energy levels.
PPE Category Labeling
Equipment labels specifying required PPE category, incident energy, and flash protection boundary per AEA 90364.
Short Circuit Integration
Coordinated with short circuit analysis to ensure accurate fault current data feeds the arc flash model.
Hazard Risk Assessment
Systematic evaluation of each work location to classify hazard severity and determine safe approach distances.
Mitigation Recommendations
Engineering controls to reduce incident energy — relay settings, bus differential protection, and zone-selective interlocking.
Compliance Documentation
Complete report package meeting AEA 90364, IEEE 1584, and NFPA 70E requirements for regulatory audits.
How We Work
Our Process
Data Collection
On-site survey of switchgear, transformers, cable runs, and protective device settings across your Argentine facility.
System Modeling
Build the electrical model in ETAP with verified utility fault contribution, impedance data, and device coordination curves.
Analysis & Calculation
Run IEEE 1584 arc flash calculations at every bus to determine incident energy, arc flash boundary, and PPE requirements.
Report & Labeling
Deliver the final report with equipment labels, one-line diagrams, and AEA 90364 compliance documentation.
Worker Safety
Protect Your Team from Arc Flash Hazards
Arc flash exceeds 19,000 °C — enough to vaporise copper and cause severe burns at distance. A study quantifies that risk and specifies how to reduce it.
- Reduces arc flash incident energy by up to 80% through engineering controls
- Equipment labels meet AEA 90364 and NFPA 70E marking requirements
- Identifies highest-risk panels and switchgear for priority mitigation
- Establishes safe approach distances and PPE categories for every work location
- Provides audit-ready documentation for ENRE inspections
Deliverables
What You Receive
Every arc flash engagement ends with a complete package aligned with IEEE 1584 and AEA 90364.
- 1Updated single-line diagrams and equipment inventory
- 2Short-circuit, coordination, and incident-energy results bus-by-bus
- 3Printed labels for every panel and piece of switchgear
- 4Ranked mitigation plan with estimated cost and incident-energy reduction
- 5Executive summary plus a full technical appendix for engineering review
FAQ
Frequently Asked Questions
What is an arc flash study?+
An arc flash study calculates the incident energy — measured in cal/cm² — at every point in your electrical system where workers might be exposed. The study determines PPE requirements, arc flash boundaries, and equipment labeling needs. It follows IEEE 1584 methodology and is required under AEA 90364 for facilities in Argentina.
How often should an arc flash study be updated?+
Arc flash studies should be updated every 5 years or whenever significant changes occur — new equipment installations, utility fault current changes, protective device modifications, or facility expansions. AEA 90364 requires current studies. An outdated study may understate hazards, leaving workers inadequately protected.
How long does an arc flash study take?+
A typical arc flash study for a medium-sized Argentine facility takes 4 to 8 weeks from initial data collection to final report delivery. Larger industrial complexes with multiple substations may require 10 to 12 weeks. The timeline depends on system complexity, number of buses, and data availability.
What PPE is required after an arc flash study?+
PPE requirements are determined by the incident energy level at each work location. Category 1 (4 cal/cm²) requires arc-rated shirt and pants. Category 2 (8 cal/cm²) adds a face shield. Category 3 (25 cal/cm²) requires a flash suit hood. Category 4 (40 cal/cm²) requires a full flash suit.
Is an arc flash study required by AEA 90364?+
AEA 90364 requires employers to assess arc flash hazards at electrical equipment where workers perform energized work. This assessment must include incident energy calculations, PPE determination, and equipment labeling. Carelabs delivers studies that meet AEA 90364, IEEE 1584, and NFPA 70E requirements.
Ready to Schedule Your Arc Flash Study?
Our ISO 9001:2008-accredited engineers deliver IEEE 1584 studies across Buenos Aires, Córdoba, Rosario, and Mendoza Fast turnaround, clear reports, full AEA 90364 compliance support.
Request a Free Quote